 | Chapter 8 Configuring DNS Name Service |  |
| Chapter 8 Configuring DNS Name Service | |
nslookup is a debugging tool provided as part of the BIND software package. It allows anyone to directly query a nameserver and retrieve any of the information known to the DNS system. It is helpful for determining if the server is running correctly and is properly configured, or for querying for information provided by remote servers.
The nslookup program is used to resolve queries either interactively or directly from the command line. Below is a command-line example of using nslookup to query for the IP address of a host:
%nslookup almond.nuts.comServer: peanut.nuts.com Address: 172.16.12.2 Name: almond.nuts.com Address: 172.16.12.1
Here, a user asks nslookup to provide the address of almond.nuts.com. nslookup displays the name and address of the server used to resolve the query, and then it displays the answer to the query. This is useful, but nslookup is more often used interactively.
The real power of nslookup is seen in interactive mode. To enter interactive mode, type nslookup on the command line without any arguments. Terminate an interactive session by entering CTRL-D (^D) or the exit command at the nslookup prompt. Redone in an interactive session, the previous query shown is:
%nslookupDefault Server: peanut.nuts.com Address: 172.16.12.2 >almond.nuts.comServer: peanut.nuts.com Address: 172.16.12.2 Name: almond.nuts.com Address: 172.16.12.1 >^D
By default, nslookup queries for A records, but you can use the set type command to change the query to another resource record type, or to the special query type "ANY." ANY is used to retrieve all available resource records for the specified host.
The following example checks MX records for almond and peanut. Note that once the query type is set to MX, it stays MX. It doesn't revert to the default A-type query. Another set type command is required to reset the query type.
%nslookupDefault Server: peanut.nuts.com Address: 172.16.12.2 >set type=MX>almond.nuts.comServer: peanut.nuts.com Address: 172.16.12.2 almond.nuts.com preference = 5, mail exchanger = almond.nuts.com almond.nuts.com inet address = 172.16.12.1 >peanut.nuts.comServer: peanut.nuts.com Address: 172.16.12.2 peanut.nuts.com preference = 5, mail exchanger = peanut.nuts.com peanut.nuts.com inet address = 172.16.12.2 >exit
You can use the server command to control the server used to resolve queries. This is particularly useful for going directly to an authoritative server to check some information. The following example does just that. In fact, this example contains several interesting commands:
First we set type=NS and get the NS records for the zoo.edu domain.
From the information returned by this query, we select a server and use the server command to direct nslookup to use that server.
Next, using the set domain command, we set the default domain to zoo.edu. nslookup uses this default domain name to expand the hostnames in its queries, in the same way that the resolver uses the default domain name defined in resolv.conf.
We reset the query type to ANY. If the query type is not reset, nslookup still queries for NS records.
Finally, we query for information about the host tiger.zoo.edu. Because the default domain is set to zoo.edu, we simply enter tiger at the prompt.
%nslookupDefault Server: peanut.nuts.com Address: 172.16.12.2 >set type=NS>zoo.eduServer: peanut.nuts.com Address: 172.16.12.2 Non-authoritative answer: zoo.edu nameserver = NOC.ZOO.EDU zoo.edu nameserver = NI.ZOO.EDU zoo.edu nameserver = NAMESERVER.AGENCY.GOV Authoritative answers can be found from: NOC.ZOO.EDU inet address = 172.28.2.200 NI.ZOO.EDU inet address = 172.28.2.240 NAMESERVER.AGENCY.GOV inet address = 172.21.18.31 >server NOC.ZOO.EDUDefault Server: NOC.ZOO.EDU Address: 172.28.2.200 >set domain=zoo.edu>set type=any>tigerServer: NOC.ZOO.EDU Address: 172.28.2.200 tiger.zoo.edu inet address = 172.28.172.8 tiger.zoo.edu preference = 10, mail exchanger = tiger.ZOO.EDU tiger.zoo.edu CPU=ALPHA OS=UNIX tiger.zoo.edu inet address = 172.28.172.8, protocol = 6 7 21 23 25 79 tiger.ZOO.EDU inet address = 172.28.172.8 >exit
The final example shows how to download an entire domain from an authoritative server and examine it on your local system. The ls command requests a zone transfer and displays the contents of the zone it receives. [12] If the zone file is more than a few lines long, redirect the output to a file, and use the view command to examine the contents of the file. (view sorts a file and displays it using the UNIX more command.) The combination of ls and view are helpful when tracking down a remote hostname. In the example that follows, the ls command retrieves the big.com zone and stores the information in temp.file. Then view is used to examine temp.file.
[12] For security reasons, many nameservers do not respond to the ls command. See the xfrnets command in Appendix C for information on how to limit access to zone transfers.
peanut%nslookupDefault Server: peanut.nuts.com Address: 172.16.12.2 >server minerals.big.comDefault Server: minerals.big.com Address: 192.168.20.1 >ls big.com > temp.file[minerals.big.com] ######## Received 406 records. >view temp.fileacmite 192.168.20.28 adamite 192.168.20.29 adelite 192.168.20.11 agate 192.168.20.30 alabaster 192.168.20.31 albite 192.168.20.32 allanite 192.168.20.20 altaite 192.168.20.33 alum 192.168.20.35 aluminum 192.168.20.8 amaranth 192.168.20.85 amethyst 192.168.20.36 andorite 192.168.20.37 apatite 192.168.20.38 beryl 192.168.20.23 --More-- q >exit
These examples show that nslookup allows you to:
Query for any specific type of standard resource record.
Directly query the authoritative servers for a domain.
Get the entire contents of a domain into a file so you can view it.
Use nslookup's help command to see its other features. Turn on debugging (with set debug) and examine the additional information this provides. As you play with this tool, you'll find many helpful features.
|  | |
| 8.3 Configuring named |  | 8.5 Summary |