Activated Sludge Process - 9...

Dewatering...

1. Vacuum Filtration...

The vacuum filter for dewatering sludge is a drum over which is laid the filtering medium consisting of a cloth of cotton, wool, nylon, dynel, fiber glass or plastic, or a stainless steel mesh, or a double layer of stainless steel coil springs. The drum with horizontal axis is set in a tank with about one quarter of the drum submerged in conditioned sludge. Valves and piping are so arranged that, as a portion of the drum rotates slowly in the sludge, a vacuum is applied on the inner side of the filter medium, drawing out water from the sludge and holding the sludge against it. The application of the vacuum is continued as the drum rotates out of the sludge and into the atmosphere. This pulls water away from the sludge, leaving a moist mat or cake on the outer surface. This mat is scraped, blown or lifted away from the drum just before it enters the sludge tank again.

The common measure of performance of vacuum filters is the rate in pounds per hour of dry solids filtered per square foot of filter surface. For various sludges this rate may vary from a low of 2.5 for activated sludge to a high of 6 to 11 for the best digested primary sludge. The moisture content in the sludge cake also varies with the type of sludge from 80 to 84 percent, for raw activated sludge to 60 to 68 percent for well digested primary sludge.

While operating costs, including conditioning of sludge for vacuum filtration, are usually higher than with sludge beds, filtration has the advantage of requiring much less area, is independent of seasons and weather conditions, and can eliminate the necessity for digestion since raw sludge can be dewatered sufficiently to be incinerated. The details of operation of a vacuum filter vary somewhat, depending on the make of filter, the chemicals used for conditioning and the type of sludge to be handled. There are however, a few general suggestions on operation which should be considered, such as :

- Conditioned sludge should be filtered as quickly as possible after the addition of the chemicals and adequate mixing. Continuous feeding is preferable to batch conditioning.
- In raw sludge filtration, fresh sewage solids and sludge filter more readily than stale or septic sludge. The applies to a raw sludge filtration.
- Completely digested sludge usually filters more readily than partially digested sludge.
- The concentration of sludge to be filtered is critical as sludge with the higher solid content usually filters more readily than that with a lower solid content.
- The presence of mineral oils and wastes from dry cleaning establishments makes sludge filtration difficult. Such wastes should, therefore, be kept out of the sewer system and disposed of separately.
- Prolongation of the life of the material used as the filter may be effected by proper care. Such care includes washing of the filter material with the spray jets after every period of use, removal of grease and fats with warm soap solution if clogged, treatment with diluted hydrochloric acid for removal of lime encrustations, maintenance of scraper bade in careful adjustment to filter drum to prevent tearing of the filter material.
- Diluted ferric chloride solutions (10% to 20%) usually give better results in the conditioning of the sludge.
- A high calcium lime is preferable or sludge filtration work.
- The maintenance of a uniform vacuum is necessary for satisfactory operation. Loss or fluctuations in vacuum usually indicate a break in the filter material, poorly conditioned sludge or uneven distribution of the sludge solids in the filter pan.
- Avoid excessive use of chemicals. The quantities of chemicals used for conditioning can be frequently reduced by careful control of the mixing and flocculation equipment.
- After every use the vacuum filter should be cleaned, and all sludge drained from the unit. This sludge and wash water should not be returned to the sludge storage tank but to the raw sewage channel or to a digester.

2. Pressure Filtration...

Pressure filtration is a process similar to vacuum filtration where sludge solids are separated from the liquid. Leaf filters probably are the most common type of unit.

Like vacuum filtration, a porous media is used in leaf filters to separate solids from the liquid. The solids are captured in the media pores; they build up on the media surface; and they reinforce the media in its solid-liquid separation action. Sludge pumps provide the energy to force the water through the media.

Lime, aluminum chloride, aluminum chlorohydrate, and ferric salts have been commonly used to condition sludge prior to pressing. The successful use of ash precoating has also been reported. Minimum chemical costs are supposed to be the major advantage of press filters over vacuum filters.

Leaf filters represent an attempt to dewater sludge in a small space quickly. But, when compared to other dewatering methods, they have major disadvantages: (1) batch operation, and (2) high operation and maintenance costs.

Some other types of pressure filters include hydraulic and screw presses, which while effective in dewatering sludges, have a major disadvantage of usually requiring a thickened sludge feed.

Sludge cakes as high as 75% solids using pressure filtration have been accomplished at the Geneva, New York Sewage Treatment Plant.

3. Centrifugation...

Basically, centrifuges separate solids from the liquid through sedimentation and centrifugal force. In a typical unit sludge is fed through a stationary feed tube along the centerline of the bowl through a hub of the screw conveyor. The screw conveyor is mounted inside the rotating conical bowl. It rotates at a slightly lower speed than the bowl. Sludge leaves the end of the feed tube, is accelerated, passes through the ports in the conveyor shaft, and is distributed to the periphery of the bowl. Solids settle through the liquid pool, are compacted by centrifugal force against the walls of the bowl, and are conveyed by the screw conveyor to the drying or beach area of the bowl. The beach area is an inclined section of the bowl where further dewatering occurs before the solids are discharged. Separated liquid is discharged continuously over adjustable weirs at the opposite end of the bowl.

Parameters : In centrifugation, process variables are: (1) feed rate, (2) sludge solids characteristics, (3) feed consistency, (4) temperature, and (5) chemical additives. Machine variables are: (1) bowl design, (2) bowl speed, (3) pool volume, and (4) conveyor speed.

Two factors usually determine the success of failure of centrifugation - cake dryness and solids recovery. The effect of the various parameters on these two factors are listed below :

To Increase Cake Dryness	To Increase Solids Recovery
Increase bowl speed	Increase bowl speed
Decrease pool volume	Increase pool volume
Decrease conveyor speed	Decrease conveyor speed
Increase feed rate	Decrease feed rate
Decrease feed consistency	Increase temperature
Increase temperature	Use flocculents
Do no use flocculents	Increase feed consistency

Centrifugation has some inherent advantages over vacuum filtration and other processes used to dewater sludge. It is simple, compact, totally enclosed, flexible, can be used without chemical aids, and the costs are moderate. Industry particularly has accepted centrifuges in part due to their low capital cost, simplicity of operation, and effectiveness with difficult-to-dewater sludges.

Theory and Operation : The most effective centrifuges to dewater waste sludges are horizontal, cylindrical - conical, solid bowl machines. Basket centrifuges dewater sludges effectively but liquid clarification is poor. Disc-type machines do a good job of clarification but their dewatering capabilities leave much to be desired.

Centrifuges are being installed in more and more wastewater treatment plants for the following reasons: (1) the capital cost is low in comparison with other mechanical equipment, (2) the operating and maintenance costs are moderate, (3) the unit is totally enclosed so odors are minimized, (4) the unit is simple and will fit in a small space, (5) chemical conditioning of the sludge is often not required, (6) the unit is flexible in that it can handle a wide variety of solids and function as a thickening as well as a dewatering device, (7) little supervision is required, and (8) the centrifuge can dewater some industrial sludges that cannot be handled by vacuum filters.

The disadvantages associated with centrifugation are: (1) without the use of chemicals the solids capture is often very poor, and chemical costs can be substantial; (2) trash must often be removed from the centrifuge feed by screening; (3) cake solids are often lower than those resulting from vacuum filtration; and (4) maintenance costs are high.

The poor quality of the centrate is a major problem with centrifuges. The fine solids in centrate recycled to the head of the treatment plant sometimes resist settling and as a result, their concentrations in the treatment system gradually build up. The centrate from raw sludge dewatering can also cause odor problems when recycled. Flocculents can be used to increase solids captures, often to any degree desired, as well as to materially increase the capacity (solids loading) of the centrifuges. However, the use of chemicals nullifies the major advantage claimed for centrifuges - moderate operating costs.

4. Drying Beds...

Drying beds are generally used for dewatering of well digested sludges. Attempts to air dry raw sludge usually result in odor problems.

Sludge drying beds consist of perforated or open joint drainage pipe laid within a gravel base. The gravel is covered with a layer of sand. Partitions around and between the drying beds are generally open to the weather but may be covered with ventilated green-house type enclosures where it is necessary to dewater sludge in wet climates.

The drying of sludge on sand beds is accomplished by allowing water to drain from the sludge mass through the supporting sand to the drainage piping and natural evaporation to the air. As the sludge dries, cracks develop in the surface allowing evaporation to occur from the lower layers which accelerates the drying process.

Many design variations are used for sludge drying beds, including the layout of the drainage piping, thickness and type of materials in the gravel and sand layers, and construction materials used for the partitions. The major variation is whether or not the beds are covered. Any covering structure must be well ventilated. In the past, some beds were constructed with flat concrete bottoms for drainage without pipes, but this construction has not been very satisfactory. Asphalt concrete (blacktop) has been used in drying beds in Onondaga County and the Village of Sydney operations with great success.

The only sidestream is the drainage water. This water is normally returned to the raw sewage flow to the plant or to the plant headworks. The drainage water is not normally treated prior to return to the plant.

Experience is the best guide in determining the depth of sludge to be applied, however, typical application depth is 8 to 12 inches. The condition and moisture content of the sludge, the sand bed area available, and the need to draw sludge from digesters are factors to consider. Do no apply fresh sludge on top of dried sludge in a bed.

The best time to remove dried sludge from drying beds depends on a number of factors, such as subsequent treatment by grinding or shredding, the availability of drying bed area for application of current sludge production, labor availability, and, of course, the desired moisture content of the dried sludge. Sludge can be removed by shovel or forks at a moisture content of 60 percent, but if it is allowed to dry to 40 percent moisture, it will weigh only half as much and is still easy to handle. If the sludge gets too dry (10 to 20 percent moisture) it will be dusty and will be difficult to remove because it will crumble as it is removed. Many operators of smaller treatment plants use wheelbarrows to haul sludge from drying beds. Planks are often laid on the bed for a runway so that the wheelbarrow tire does not sink into the sand. Wheelbarrows can be kept close to the worker so that the shoveling distance is not great. Most plants use pick-up trucks or dump trucks to transport the sludge from the drying bed. Dump trucks have the advantage of quick unloading and most municipalities have dump trucks available. Where trucks are used, it is best to install concrete treadways in the sludge drying bed wide enough to carry the dual wheels since the drying bed can be damaged if the trucks are driven directly on the sand. The treadways should be installed so that good access is provided to all parts of the beds. If permanent treadways have not been installed, heavy planks may be placed on the sand. Large plants will normally utilize mechanical equipment for handling the dried sludge. Some communities have encouraged public usage of the dried sludge. In some cases users are allowed to remove the sludge from the beds, but this may not be satisfactory in many cases. Local regulations should be reviewed before attempting to establish a public utilization program.

5. Sludge Lagoons...

The considerable labor involved in sludge drying bed operation may be avoided by the use of sludge lagoons. These lagoons are nothing but excavated areas in which digested sludge is allowed to drain and dry over a period of months or even a year or more. They are usually dug out by bulldozers, or other dirt-moving equipment, with the excavated material used for building up the sides to confine the sludge. Depths may range from two to six feet. Areas vary, and although drainage is desirable, it is not usually provided.

Digested sludge is drawn as frequently as needed, with successive drawings on top of the previous ones until the lagoon is filled. A second lagoon may then be operated while the filled one is drying. After the sludge has dried enough to be moved, a bulldozer, or a tractor with an end-loader, may be used to scoop out the sludge. In some locations it may be pushed from the lagoon by dozers into low ground for fill.

Lagoons may be used for regular drying of sludge, re-used after emptying, or allowed to fill and dry, then leveled and developed into lawn. They can also be used as emergency storage when the sludge beds are full or when the digester must be emptied for repair. In the latter case it should be treated with some odor control chemicals, such as hydrated or chlorinated lime.

The size of the lagoon depends upon the use to which it will be put. Lagoons may take the place of sludge beds or provide a place for emergency drawings of sludge, but they may be unsightly and even unwanted on a small plant site. However, they are becoming more popular because they are inexpensive to build and operate.